![]() Shielding the photo during development time (check the back of your film package for specific times) will ensure that you get deeper saturation, sharper details and that your final image is not washed out.įull article: Shielding your photos from light However, it will still be sensitive to light! It should still be kept shielded from strong light sources. This allows enough time for the blue opacification layer to spread over the whole image.Īfter the first few moments have passed, your photo can be removed from under the film shield. During these sensitive first few seconds, the film shield installed on your camera will extend on top of the photo and protect it from light. Polaroid film is sensitive to light even after it has been ejected from the camera. You can minimize the effect of heat by letting the photo process in cooler surroundings, such as an air-conditioned room, an insulated bag, or beneath a cold beverage (be careful to avoid moisture though!).įull article: How temperature affects Polaroid film When shooting at higher temperatures, cool your film packs in the fridge before taking them outside. Temperatures significantly outside of that range can affect Polaroid instant film in terms of development time and color.Ībove 28☌ (82☏), color photos tend to develop with a yellow/red tint. Polaroid film works best in temperatures between 13 – 28☌ (55 – 82☏). If you have a big empty room behind your subject, the background of the photo will likely be all black.įull article: Exposure Compensation on your Polaroid Camera When shooting indoors with flash, it's best to have your subject stand in front of a wall or backdrop so the flash has something to bounce off of, back to the camera, to make brighter photos. Keep in mind that the built-in flash on Polaroid cameras is usually only effective in a range of 1 – 2.5 meters (3.3 – 8.2 ft). If you are shooting using your camera’s built-in flash, make sure that the lighten/darken wheel or slider of your camera is adjusted to the middle position. We recommend that you adjust the exposure wheel or slide on your Polaroid camera 1/3 towards the darken setting when shooting in bright, well-lit conditions. This means that our film is more sensitive to light, or “faster”. Polaroid's current generation of SX-70 film has a slightly higher ASA/ISO than its traditional Polaroid counterpart. This list includes: i-Type, 600, and 8x10 Film. Most Polaroid film types have the correct/original ASA and do not require exposure compensation. We recommend checking the rollers of your camera before inserting each pack of film, and cleaning them regularly – even when they look clean to the naked eye.įull article: How to clean your camera rollers They are accessible by opening the film door compartment of the camera, and can be easily cleaned with a soft cloth, dampened with clean water. ![]() Therefore, you should regularly check that the rollers of your camera are clean. This is the most common source of undesirable film defects. If they are dirty, the chemistry will not be spread evenly. In order to spread the chemistry between the negative and positive part of the photo, the picture goes through two rollers found inside the film door of your camera. You will still still get some variety of result from expired film, but there may be artefacts or defects for which we are unable to accept warranty claims. While proper storage will mitigate the effects of chemical aging, the expiration date marks the point in this process after which it is unlikely that the film will produce images that meet our standards of quality. We recommend allowing at least 1 hour to allow your film to return to ambient temperature before shooting.Īll Polaroid film should be used within 12 months of production date for best results (you can find the production date stamped on the bottom of each film package).Ĭhemical changes occur as our film ages, and this will eventually affect how well your film performs. Therefore, it must be allowed to return to room temperature before use. Our film will not perform as desired at cooler temperatures. Do not freeze your film packs! This will damage the chemistry and your film will not perform properly when used. ![]() We recommend storing our film flat inside a fridge at a constant temperature between 4 – 18☌ / 41 – 65☏. Polaroid film packs should be stored in their unopened, sealed packaging in a cool and dry environment. Proper storage of Polaroid film will ensure that the film chemistry remains stable and that your photos achieve and retain the best color, contrast and detail for as long as possible. Proper storage (undeveloped / unexposed Film)
0 Comments
Leave a Reply. |